double shot combi box mold

 

此幻灯片需要JavaScript支持。

Focare Mould, China top double component mold maker, quality offer multi k plastic clip box mold, two injection moover box, bi box handy mold, double colour combi box mold, 2k plastic multibox mold.

As product and mold design of two-color mold, it need to be paid attention to:

  • Water transport arrangement of two CAVITY and CORE should be as sufficient as possible, should be balanced and same. All water-carrying joints come out from side and connect to water-carrying seat connection in the middle of code formwork
  • Pay attention to positioning of front and rear molds; inclination drop of all insertion and breaking surfaces should be as large as possible, and should be more than 0.1mm.

If you’re still looking for the good dual material mold maker in China, I’m sure we can be your another good choice.

Lucia

focaremould@yahoo.com

dual colour omni box mold

multi injection plastic clip box

2k spinning box mold

Focare Mould, China top multi k mold maker, quality offer twin injection textil box, multiple shot totem box mold, dual colour omni box mold, 2k spinning box mold, double plastic unibox mold.

As product and mold design of two-color mold, it need to be paid attention to:

  • Note that during second injection, will flow of plastic impel first molded product to deform its glue position? If this is possible, there must be a way to improve it.
  • Before A and B plates are closed, pay attention to whether front mold Slider or Lifter will reset and crush product? In this way, we must find a way to make A and B plates to close mold first, and then SLIDER or LIFET of front mold can be reset.

If you’re still looking for the good double color mold maker in China, I’m sure we can be your another good choice.

Lucia

focaremould@yahoo.com

two color collapsible liter snap lid storage mold

multi shot folding tidy tote mold

two color collapsible buckle down storage mold

Focare Mould, China top dual component mold maker, quality offer twin material collapsible buckle up plastic box mold, bi component liter snap lid storage mold, multiple injection bucklebox, bi box latching container mold.

As product and mold design of two-color mold, it need to be paid attention to:

  • After front and rear molds of mold are rotated 180º from center, they must be matched. During design, mold rotation action must be checked.
  • During injection molding, product size of the first injection molding can be slightly larger, so that it can be pressed more tightly with another CAVITY during second molding to achieve effect of

Soft and hard rubber two-color products have more details to be considered than single-color products, difficulty of mold design is greatly increased. It is important to grasp details of design, otherwise various problems will easily occur in mold trial.

If you’re still looking for the good twin material mold maker in China, I’m sure we can be your another good choice.

Lucia

focaremould@yahoo.com

two shot snap down buckle box mold

bi injection snap handle caddy bin

Focare Mould, China top bi shot mold maker, quality offer bicolors wheeled tool box mold, dual injection snap on tool box, twin shot snap buckles mold, bichrome snap fitting box mold.

As product and mold design of two-color mold, it need to be paid attention to:

When designing CAVITY for second injection, in order to prevent CAVITY from inserting (or scratching) glue position of product that has been molded for the first time, a part of void can be designed. However, strength of each sealing position must be carefully considered, that is, in injection molding, is there a possibility that plastic will be deformed under a large injection pressure, which may lead to possibility of a sharp edge in second injection molding?

If you’re still looking for the good twin component mold maker in China, I’m sure we can be your another good choice.

Lucia

focaremould@yahoo.com

bi shot snap tight lid mold

multi injection storage latch box

Focare Mould, China top rotary mold maker, quality offer bi shot snap tight lid mold, double buckle down snap handles mold, multi injection snap lid box container, twin color buckle containers mold.

As product and mold design of two-color mold, it need to be paid attention to:

  • Two mold bases of Asian two-color are exactly same. When ordering mold bases, you need to pay attention to machining accuracy, which is convenient for exchange and clamping.
  • Shapes of two front mold cavities are different, and one product is molded respectively. Then two shapes of back mold are exactly same. Since rear mold has a soft rubber position, when soft glue is injected, ejector plate retreats, leaving a space for soft rubber to enter glue. When injection molding ABS, long guide post is used to bounce thimble plate through seesaw.

If you’re still looking for the good biocolor mold maker in China, I’m sure we can be your another good choice.

Lucia

focaremould@yahoo.com