2k automotive parts mold – 第 3 页 – china quality 2k molds maker

two colour wing flaps mold

2024-03-172024-03-17Leave a comment

YUEYI Mold, China experienced 2k mold maker, quality offer dual injection thermoregulation flaps mold, rubber temperature regulator flap bi mold, double colour climate heater flap mold, bi component temp control damper mold.

As we all know injection mold cycle time is very important for moulds and molds buyer.

Firstly let’s talk about the mould design. In some factories the young designers do not have much experience, sometimes they designed mould structure is unreasonable. And the problem been found till the moulds testing, then the mould maker need to spend a lot of time and effort to rectify the mould. So, a good mould design is the fundamental and first step to ensure deliver on time.

Secondly, correct and suitable tooling should be taken. Many mould makers in order to save tooling cost, they do not use high precision tooling equipments and the work piece is not meet precision requirements, then mould maker need to re-tooling or change the part. It’s waste of time!

If you’re still looking for the good two colour wing flaps mold maker in China, we can be your another good choice.

Lucia

lucia@yueyimold.com

dual component sidedraft damper mold

2024-03-17Leave a comment

YUEYI Mold, China experienced 2k mold maker, quality offer bi shot barometric damper mold, dual component sidedraft damper mold, double material side vent flaps mold, double color windshield heater flaps mold.

Injection mold in production, need regular maintenance, primary maintenance are as follow:

– During the production process, wipe with a cloth every 8 hours on the parting surface both core and cavity side. But attention not to wipe mirror polished or textured core to avoid scratch.
– During production process need to give guide pin, slider or sliding parts coated with lubricant once a day, play a ejector pin oil, to prevent wear damage or stuck.
– Each shift should check whether the slider and ejector pin moves abnormal, spring is broken?
– If found any problem should immediately stop production.
– When found the product stick to cavity or core, should immediately stop production and don’t use diagonal pliers to take out the product.
– If production stops, regardless of short time stop, required to immediately turn off the chilled water to prevent mold rust.
– When take off the mold from the IMM, must ensure no water left in the cooling line and mold. Wipe clean the parting surface and check whether there is mold damage.

If you’re still looking for the good bi mold replacement damper maker in China, we can be your another good choice.

Lucia

lucia@yueyimold.com

two color leaky adaptive damper mold

2024-03-17Leave a comment

YUEYI Mold, China experienced 2k mold maker, quality offer multi injection airfoil control damper mold, dual material heat control damper mold, two color leaky adaptive damper mold, bi component HVAC balancing damper mold.

Injection mold in production, need regular maintenance, the maintenance doable in the injection molding machine is called primary care. The reason to do primary maintenance is because in the production mold often occurs the following situation: the tiny material chips will be flying, volatile lubricants lead to insufficient lubrication, loose parts cause other risks and other situations. That the case is bound to happen in the case of the injection molding process, so do the maintenance is necessary.

YUEYI is a professional plastic multi component injection mold making factory which can offer you a good solution to your multi injection molding.

If you’re still looking for the good gyratory leaking dampers mold maker in China, we can be your another good choice.

Lucia

lucia@yueyimold.com

rubber feet air flaps double mold

2024-03-17Leave a comment

YUEYI Mold, China experienced double mold maker, quality offer rubber feet air flaps double mold, two colour foot well flaps mold, dual colour air flow flap mold, turntable vent leg flaps mold.

The double color mold core and cavity must match well after rotate 180°. When make the design, designer must check this action, as this has very high requirement of mold base positioning process. The total thickness of clamp plate and A plate should not less than 170mm. When design the mold, must check customer’s injection molding machine max and min mold thickness and KO hole size. When molding the products, it’s better to make the 1st color a little bit bigger, so it can fit tighter when put it to the 2nd color mold. Avoid 2nd injection melt flow makes 1st color product deform, if this situation may happen, must rectify.

If you’re still looking for the good dual shot air control flaps mold maker in China, we can be your another good choice.

Lucia

lucia@yueyimold.com

two shot temperature regulating flap mold

2024-03-17Leave a comment

YUEYI Mold, China experienced 2k mold maker, quality offer bi injection heater blend flaps, two shot temperature regulating flap mold, multi material HVAC temp flap mold, two tone climatronic flaps mold.

Now the ever-changing consumer product models require good looks, fancy design, and also to quickly meet market demand. Designers generally design the house ware products for different purposes, in different parts of different materials to meet the needs of a particular environment, and to extend the product life and increase aesthetic and practical purpose. This practical design requirements will undoubtedly lead to the production technology also will be complicated, double color injection molding process is to be born of this trend.

Double color injection molding is make two different color material injected to one same mold, to make plastic parts presents regular or irregular pattern moire-like colors to enhance the plastic parts of practicality and aesthetics.

If you’re still looking for the good rotary mold temperature control flap maker in China, we can be your another good choice.

Lucia

lucia@yueyimold.com